Imposer GUI v0.1
with
Imposer.exe v0.2 by Z33
С помощью этой утилиты можно изменять картинки, на которых имеются некоторые ресурсы из меню XMB.
Это касается двух файлов прошивки:
- Flash0\kd\impose.prx
- Flash0\kd\resource\impose.rsc
Скачать: 
Imposer Gui v0.1.rar
Readme
Imposer GUI v0.1
============= CREDITS =================
Imposer.exe v0.2 by Z33
============= GUIDE =================
TO INJECT:
1. Choose impose to open.
IMPOSE.PRX must be from 2.50+ firmware and DECRYPTED/UNPACKED!
IMPOSE.RSC must be from 2.70+ firmware!
2. Choose the bitmap to open.
BITMAP for PRX must be 332x166, unpacked 24bit BMP.
BITMAP for RSC must be 552x546, unpacked 8bit BMP.
3. Select the output folder and filename for the modified IMPOSE (PRX or RSC).
4. Click OK!
5. Open the folder/directory where you save the file and copy to flash 0: kd/ and /kn folders.
SPECIAL: IMPOSE.PRX must be from the same psp firmware when copied to flash 0: kn/
6. Done!
TO EXTRACT:
1. Choose impose to open.
IMPOSE.PRX must be from 2.50+ firmware and DECRYPTED/UNPACKED!
IMPOSE.RSC must be from 2.70+ firmware!
2. Click on Bitmap, choose a destination and type a filename, click Open.
3. Leave Output EMPTY!
4. Click OK!
5. Open the folder/directory where you save the bitmap and edit with any image editor.
BITMAP for PRX must be 332x166, unpacked 24bit BMP.
BITMAP for RSC must be 552x546, unpacked 8bit BMP.
6. Done!
============ Uncommented Imposer Manual by Z33 =============
imposer v0.2 by Z33
USAGE: imposer INPUTIMPOSE.PRX/RSC IMAGEDATA.BMP [OUTPUTIMPOSE.PRX/RSC]
If OUTPUTIMPOSE.PRX/RSC is omitted, INPUTIMPOSE.PRX/RSC is scanned for
possible bitmap and if found, is exported to IMAGEDATA.BMP. Else bitmap
from INPUTIMPOSE.PRX/RSC is replaced with IMAGEDATA.BMP and the resulting
file is written to OUTPUTIMPOSE.PRX/RSC.
IMPOSE.PRX must be from 2.50+ firmware and DECRYPTED/UNPACKED!
IMAGEDATA.BMP for PRX must be 332x166, unpacked 24bit BMP.
IMPOSE.RSC must be from 2.70+ firmware!
IMAGEDATA.BMP for RSC must be 552x546, unpacked 8bit BMP.
---------------------------------------------------------------------------
When the imagedata is exported from either prx or rsc the active region of
each of the elements is shown with a red rectangle for easier editing.
Imagedata from the rsc is somewhat tricky as each of the parts can only
contain 16 colors, and there are also two other 16 color palettes used for
the extra highlights of 'YES' and 'NO' images. YOU CAN NOT USE OTHER COLORS
FOR THESE ELEMENTS THAN WHAT THEY ARE CURRENTLY USING. Meaning you can only
use colors 0-15 for the main elements, colors 16-31 for the brightest 'YES'
& 'NO' elements and colors 32-47 for the mid-bright 'YES' & 'NO' elements.
All the other colors between 47-255 will be ignored. If you choose to mix
up colors from around the palette, the results speak for themselves,
depending of what colors you have chosen...
- Хорошо извлекает картинки из PRX с прошивки 2.50 по 3.40. Начиная с 3.50 по 3.7x извлекает немного испорченными. От 3.80 и выше - не работает.
- Хорошо извлекает картинки из RSC с прошивки 2.70 по 5.55. На 5.70 извлекает испорченной. На 6.xx вообще не работает.
|
Рекомендую не пользоваться GUI, а лучше из командной строки задавать команды на консольную утилиту
imposer.exe.
Или проще использовать батник, например для извлечения - с таким содержимым:
@echo off
IF EXIST impose.prx (
imposer impose.prx out_prx.bmp
)
IF EXIST impose.rsc (
imposer impose.rsc out_rsc.bmp
)
pause
Скопируйте данный код выше в текстовой документ и затем измените расширение TXT на BAT.
Положите в эту папку декриптованный(ые) файл(ы)
impose.prx и/или
impose.rsc, затем запускайте батник, как обычный исполняемый экзешник.
На выходе получите такие вот картинки:
impose.prx (332x166)
|
impose.rsc (552x546)
|
|
|